ROUNDBELL HOBBY PRODUCTS SMALL PARTS

MISC. ITEMS:  Our products (*) are available at better dealers. Others are only available
        from LocoDoc.

HARDENED STEEL SHAFT These Mashima motor shafts are hardened steel and have a very
     polished surface that will not wear or cause enclosing beatings to wear if lubricated even if run at
      high speeds for millions of revolutions. Mild steel shaft sold by others should not be used in any
      high speed uses. We ordered these to use in all our gearbox conversions.
*Shaft-15   I.5mm shaft                                               2.20"                                                    $2
*Shaft-20   2.0mm shaft                                               3.00"                                                    $2

MINI CONNECTORS
*MC-1 A convenient way to quickly make and break electrical connections to wipers, trucks, tenders etc.
Twenty solderable electrical sockets and wire to be soldered to the wire making the connection. PFM
offered these to ease sound system instellations.                                            (20)in pack         $3.95

SHAFT SLEEVES; these machined brass sleeves are for sleeving up various reasons. shafts for
      Not recomended for use in flywheels or gears unless there is no alternative.
*SS-1520  To convert a 1.5 mm shaft to a 2  mm shaft.    1/4"                                                    $3
*SS-1524  To convert a 1.5 mm shaft to a 2.4mm shaft   1/4"                                                     $3
*SS-2024  To convert a  2  mm shaft to a 2.4 mm shaft   1/4"                                                     $3

*SS-3037 This special collar is used on Grandt Line gearhead drives to keep the
          drive ball from spliting and spinning on the motor shaft                                                       $3

SURGICAL TUBING; For connecting shafts and making a universal joint at the connection.
*ST-15 To connect 1.2mm, 1.5mm and 2mm shafts.                    6 inches                               $1.50
*ST-20 To connect 2mm and 2.4mm shafts.                                 6 inches                               $1.50

SUPER TRACK POLISHER
*T-1 This large (3/4" x 2" x 3.25" soft rubber block has ultra fine grit that will polish metal ( track and brass
for soldering ) but not scratch and gouge the rail like the common "Bright Boys". It does not harden with age
and can be cut into many smaller blocks. It is quite soft and flexible and made in Germany.         $7.95

UNIVERSAL DRIVE SHAFT" This is the double universal and sliding spline used in our Glide Drive
      Kits. The total length can be reduced to as little as 1/2". The shaft can be lengthened by using K&S
      #149 square brass tubing cut to length. They are completely silent, "constant velocity" and very flexible.
*UDS-1 for 2mm and 2.4 mm shafts up to 1" long (2 shafts, 2 sleeves and 4 universals)                 $4.00
*UDS-1.5 for 2mm and 2.4 mm shafts up to 1.5" long (2 shafts, 2 sleeves and 4 universals)          $4.50
*UDS-2 for 2mm and 2.4 mm shafts up to 2" long (2 shafts, 2 sleeves and 2 universals)                 $5.00

PHOSPHOR BRONZE" The best material fot making flat and coil springs
            and wipers for improved electrical pick up.
FLAT SHEET
       649-8003    .003" thick x 1 5/8" x 6"                                                                                       $3.98
       649-8008    .008" thick x 1 5/8" x 6"                                                                                        $3.98
       370-15053   016" thick x 5" x 7"                                                                                             $4.19
STRAIGHT WIRE
       293-1100    .008" x 6" (10 per tube)                                                                                       $2.50
       293-1101    .010" x 6" (12)                                                                                                      $2.50
       293-1106    .0125"x 6" (12)                                                                                                    $2.50
       293-1102    .015" x 6" (12)                                                                                                     $2.50
       293-1103    .020" x 6" (12)                                                                                                    $2.50
       293-1104    .025" x 6" (12)                                                                                                    $2.50
       293-1105    .032" x 6" (12)                                                                                                   $2.50

       Go To ORDER FORM

Return to ROUNDBELL HOME PAGE

Return to LOCO DOC HOME PAGE